China Manufacturers 2.4Ghz CC2500 CC2591 1000M Spi Rf Amplifier Module

FOB Reference Price:Get Latest Price
$4.50 - $4.51 / Pieces | 10 Piece/Pieces (Min. Order)
Report Suspicious Activity
Quick Details
Model Number:
wireless module
Brand Name:
Place of Origin:
Guangdong, China
Product name:
China Manufacturers 2.4Ghz CC2500 CC2591 1000M Spi Rf Amplifier Module
Operating supply voltage:
Central frequency:
Frequency accuracy:
Modulation format:
Transmit power:
TX current consumption:
Receiver sensitivity:
RX current consumption:
Sleep State current consumption:
Supply Ability
Supply Ability:
10000 Piece/Pieces per Month
Packaging & Delivery
Packaging Details
Standard package
Lead Time :
Shipped in 3 days after payment

China Manufacturers 2.4Ghz CC2500 CC2591 1000M Spi Rf Amplifier Module



VT-CC2500PA-M1 is based on RF transceiver CC2500 of TI Chipcon. CC2500 is a low-cost 2.4 GHz transceiver designed for very low power wireless applications. The circuit is intended for the 2400-2483.5 MHz ISM (Industrial, Scientific and Medical) and SRD (Short Range Device) frequency band. The max RF output power can be set as high as +1dBm, with data rate as high as 500Kbps. The module integrated PA CC2591 to make the max RF output power up to +20dBm. There is an inverted F antenna on the module. So you can use the module conveniently and reducing your development time.    

Detail Parameters



Test operating conditions:Ta=25°C,VCC=3.3V if nothing else stated.





Operating supply voltage

DC 2.4~3.6V


Central frequency


Can be programmable to other frequency in bands 2400~2483.5MHz

Frequency accuracy



Modulation format



Transmit power



TX current consumption



Receiver sensitivity



RX current consumption



Sleep State current consumption


Refer to IC operation states

Data rate



Spurious emissions and harmonics

< -30dBm

TX power +10dBm.

Communication distance


2-FSK modulation, 2.4kbps data rata, +20dBm output power.

Antenna impedance


Multilayer Chip Antenna

Operating temperature

-20~+85 °C


Storage temperature range





See more in PCB description


1. The module transmission data rate will affect Transmission distance ,the higher the data rate , the closer the distance, and the lower the receiving sensitivity.

2. The supply voltage to the module will affect TX power, in the operating supply voltage range, the lower the voltage, the lower the TX power.

3. The module central frequency will change as the operating temperature change, use it under suggest temperature, the module can work well.

4. The antenna will strongly affect the communication distance, please select matched antenna and connect it correctly.

5. The module mount will affect the communication distance.




Related Product



Pin name

Pin type




2.4 V - 3.6 V analog power supply connection.



Connect to the system ground.


Digital Input

Serial configuration interface, data input.


Digital Input

Serial configuration interface, clock input.


Digital Output

Serial configuration interface, data output.

Optional general output pin when CSN is high.


Digital I/O

Programmable Clock output, down-divided from XOSC


Digital I/O

Programmable Clock output, down-divided from XOSC.


Digital Input

Serial configuration interface, chip select, active low.



RF output signal from PA, connect to the Antenna.


Digital Input

RX mode:LNA=0(Low);PA=1(High)

TX mode:LNA=1(High);PA=0(Low)


Digital Input





1. The module power supply voltage range is DC 2.4~3.6V, above DC 3.6V, the module will damage. It is recommended work at DC 3.3 V.

2. The module interface use half circle pad to soldering on the system PCB board, the GND must soldering to the system digital GND reliably.

3. The antenna must the get to the module’s ANT pin as close as possible.

4. The MCU which don’t have integrated SPI interface can also control the module, use the normal I/O port to work like SPI timing to read and write. The SPI data rate is below 10MHz.

5. The interface can connect directly to the MCU which use 3.3V power supply, there is no need serial resistor. If the I/O is open-drain, the pull-up resistor will be added. When connect to the MCU which use 5V power supply, the MCU’s I/O output current beyond 10 mA, a 2~5k ohm resistor will be series to divide the voltage, or it will damage the module.

6. The module’s pin GDO0 is a general digital I/O port, it can be programmable to produce trigger signal or clock output.

7. The PA control voltage have an effect on the communicate distance and power consumption. In transmit mode, set TE=0 and RE=1; in receive or sleep mode, set TE=1 and RE=0.

      8.In the multiple channel application, the channel spacing is recommended to set           as 1MHz, or there will be a same frequency interference.

Company Information


Packaging & Shipping




Reason and Solution

Can’t communication

1.The power supply connect not well, check the module VCC whether it is out of maximum rating.

2.The signal line connect not well, check the module SPI interface.

3.The settings of the transmitter module and receiver module are not the same. Check these modules’ register configuration.

4.Signal block. If the transmitter work with a high TX power, and the receiver was put at a short distance(<0.5m), maybe there is a signal block to make no communication.

Communication distance is too short

1.The application environment is too bad or the antenna is shield. Put the antenna to a better place outside or higher throw a coaxial line , replace it with a higher gain antenna.

2.The work space contains a same frequency interference source, or a strong magnetic field interference, power source disturbance. Try to change the carrier frequency or get far away from the source of the disturbance.

3.The power supply is not strong. Check the voltage and the current whether it is enough.

High data error

1.The power supply ripple is too big, Change the power supply.

2.Check the module register configuration, it is recommended to set as the CC1120-datasheet.

3.There is a carrier frequency interference, change the channel.

4.The antenna unmatched to the module RF interface, change another matched antenna.


You May Like
Not exactly what you want? 1 request, multiple quotations Get Quotations Now >>
You May Like